My Beast of a 300zx

[Boomin33]

Not much to do with NSX ( although I thought the interior very similar when I 1st sat in an NSX )

... but going to put some work into my Zed over the next month and sell.

Just sits in the garage year after year... so the wife said it has to go.

click on the below link and check out one of my toys ;)

Link => http://www.300zx.co.uk/forum/vbpicgallery.php?do=view&g=425






...

[simonprelude]

You are not logged in or you do not have permission to access this page. This could be due to one of several reasons:

1. You are not logged in. Fill in the form at the bottom of this page and try again.
2. You may not have sufficient privileges to access this page. Are you trying to edit someone else's post, access administrative features or some other privileged system?
3. If you are trying to post, the administrator may have disabled your account, or it may be awaiting activation.

[Boomin33]

hmm bummer... I'd post my log-in details here but don't think that would be wise.

http://i119.photobucket.com/albums/o136/boomin33/i3091.jpg


Here is the spec.

1990 UK MODEL LWB 300ZX TT

549.8 FWHP - 460 Rear wheel / 6643 (173 mph) 461.8 lbft / 5282 - 1:4 BAR BOOST (2007)

August 2009 - One last push about to start to make the magic 500 at the wheels.... (up-rated fuel pump, fuel pressure regulator, Wide Band Gauge needed)

Then it will sadly it may have to go!! Unless I fall in love with it again http://www.300zx.co.uk/forum/images/smilies/wink.gif

Over £42,000 in Receipts for this build.

ENGINE:

FARNDON BILLET CRANK & CON-RODS
JE RACING LOW COMP PISTONS

- S.E NISSAN GAS FLOWED HEADS
- POLISHED & MATED INLET MANIFOLD
- FAST ROAD CAMS
- HKS 740 Injectors
- HKS 25-30 SPORTS TURBINES
- HKS DUAL INTERCOOLERS
- HKS DUAL SEQUENTIAL DUMP VALVES
- UPGRADED OIL COOLER
- CUSTOM DUAL STAINLESS EXHAUSTS
- HKS DUAL AIR FILTERS
- RPS CLUTCH
- RPS LIGHTENED FLYWHEEL
- UNORTHODOX LIGHTENED/BALANCED PULLEY

M800 MOTEC ENGINE MANAGEMENT SYSTEM (FULLY PROGRAMMABLE WITH LAPTOP LINK-UP

RUNNING GEAR:

- NISMO UPRATED BUSHES THROUGHOUT
- TOKICO ADJUSTABLE SHOCKS
- EIBACH SPRINGS
- STILLEN ADJUST FRONT/REAR ANTI-ROLL BARS
- S.E.NISSAN TORSION BARS

- A.P. RACING 4 PISTON CALIPERS
- BIG DISC CONVERSION
- GOODRIDGE FLEXIBLE HOSES

- OZ 18" SPLIT RIMS

INTERIOR

- 8 POINT WELDED IN ROLL CAGE
- LIGHT WEIGHT COBRA CARBON KEVLAR BUCKET SEATS
- WILLANS FOUR POINT HARNESSES
- PROFFESIONAL ALCANTARA RE-TRIM

BODY:

- ONE OFF FRONT BUMPER
- VENTED FRONT WINGS AND BACK PANEL
- CARBON FIBRE BONNET
- CARBON FIBRE REAR WING

'PETROL FILL' REDIRECTED TO INSIDE BOOT OF CAR - FULL ALUMINIUM CASE / SAFETY UNIT

[Silver Surfer]

I'll give you a generous £1000 for it...;)

SS

[Boomin33]

Been told that a couple have gone to Europe for £8K+. I was expecting around £6,000

I could part it out for around £10K; so even though it would take 6 months... am thinking about going that route. Messy but figure most of the Zed crowd would do the work themselves...


Going to try and get it up to 500 BHP at the wheels first though :overhead:

[mart155]

Lovely looking car mate, I always liked the 300ZX